Subea SCD100, 5.5 mm Neoprene Full Scuba Diving Wetsuit, Men’s

Wet-type full 1-piece wetsuit, made of 100% stretch 5.5 mm panels (with production tolerance). 5 mm neoprene foam, covered with nylon fabric on both sides. Seams taped using a GBS (glued and blind-stitched) assembly. The wetsuit is equipped with reinforcements on the knees to increase resistance.

The seams of the suit and hood are waterproof, with a glued and blind-stitched (GBS) assembly: the neoprene is glued first of all, then sewn for maximum resistance (the sewing needle does not go completely through the neoprene in order to prevent water infiltration).

1-piece with an attached hood equipped with the Air Expulse system: a system to evacuate air bubbles trapped in the hood. Easy to put on with the diagonal zipper on the front of the wetsuit. No underarm seams for easier arm movements.

This scuba diving suit provides thermal protection that has been tested by the independent INPP institute (Marseille, France) in order to validate its compliance with the current standard (EN 14225-1:2017). CLASS C certified wetsuit: A (+7°C/+12°C / +45°F/+54°F) B (+10°C/+18°C / +50°F/+64°F) C (+16°C/+24°C / +61°F/+75°F) D (+22°C/+30°C / +72°F/+86°F).

When diving, cold is your worst enemy! Using the right thermal protection based on the water temperature, is essential. This concept was created to keep you from having to purchase different wetsuits for different diving conditions, with 5 pieces that can be combined with your wetsuit depending on the temperature. In this way, you can complete your thermal insulation with a hood, a neoprene top, a top with a hood, a 1 mm under-shorty or a 5.5 mm over-shorty.

This is the most common type of diving suit on the market. It is not designed to keep the water out but to trap it so that your body then warms it up, creating a thermal buffer between you and the outside. Made of neoprene - a rubber polymer filled with air bubbles - these wetsuits are available in thicknesses of 0.5 to 7 mm. Thanks to their suppleness and modularity, they make excellent diving wetsuits.

Put your foot in a plastic bag, then slip your leg into your wetsuit. You entire foot comes out without snagging! To adjust, ask someone to blow into your sleeve from the wrist. The incoming air inflates the interior of the neoprene wetsuit, immediately separating it from your skin. You can then easily proceed with the final adjustments.

1) Soak the inside and the outside of the wetsuit in clean water after each session. 2) Clean with a bactericide solution. 3) Rinse thoroughly in clean water. 4) Dry on a wide hanger in a dark and well ventilated place. Caution: the sun will cause the colors of the textile parts of the wetsuit to fade and speeds up the aging process of the neoprene. Zipper fasteners can be cleaned with a toothbrush and lubricated with silicone grease

1) After each session, soak the wetsuit in clean water, on the outside and the inside 2) Use a bactericide solution to clean 3) Rinse thoroughly in clean water 4) Dry on a large hangar in a well ventilated place in the shade. Caution: the sun will cause the colors of the textile parts of the wetsuit to fade and speeds up the aging process of the neoprene. Zip fasteners can be cleaned with a toothbrush and lubricated with silicone grease.

Tribord Diving is now called SUBEA, the Decathlon brand dedicated to underwater sports (snorkeling, SCUBA diving, spearfishing and free-diving). The markings on all our diving products will gradually be replaced. Why SUBEA? Because: "SUBaquatic Experiences are Amazing"! For more information: www.subea.com

Imported

Designed and tested by our teams and our technical partner in Hendaye (France) to approve the thermal insulation.

Dry your wetsuit out of the sun and well clear of all sources of heat. Store your wetsuit on a hanger to keep its shape and conserve the neoprene.