Wedze All Road 900, Snowboard Boots, Men's

In its second year, this model has already been improved. Your feedback on the Foraker 500 model have shown that comfort can be improved. The All Road 900 has the same foam, stiff enough to hold the foot but too firm to be to everyone's comfort. We therefore applied the same improvements to the All Road 900: softer foam and still thermoformable. Support, stiffness and now comfort for all are the advantages of these shoes.

Double Cable Lock: 2 very powerful fastening wheels with cable. There are 2 clamping zones to adjust the clamping as desired for each zone. At the bottom: the force of the first wheel is concentrated on the instep to give the required support. At the top: the 2nd wheel prevents incorrect tibia movements inside the snowboard shoe. You can also tighten less to soften the shoe, or more to stiffen it with the same support (bottom tightening).

The All Road 900 offers a medium to rigid flex. Compared to the Foraker 500, it offers better board control on hard slopes at full speed, and is also more robust on landing after big jumps. The uncoupled clamping allows you to: - tighten more to make the shoe stiffer (on-piste use, freeriding and freestyle jumps) - tighten less to loosen the shoe (less strenuous runs and playful freestyle: flat, jib)

Foot support is essential when snowboarding, to be able to correctly steer your board (foot in the liner, and liner in the shoe). The level 3 liner applies 6 concepts: 1. Thermoformable liner alone, at home 2. Ergonomic Heel Pad ankle foam 3. "2-point + strap" liner fastening 4. Hook & Loop Link between the liner and shoe 5. Double layer of foam at the tongue on the instep, for support and comfort 6. 3D insole.

1. Heat your oven, rotary heat mode, to 175°F 2. Remove the inner soles from the liners, place the liners on the oven plate covered with a piece of baking paper 3. Wait 15 minutes 4. Put the hygiene insoles back, put on a pair of ski/snowboard socks, put the liners on your feet and tighten them fully. 5. Put the boots on and tighten fully 5. Wait for 15 minutes, without moving. Repeat as often as you like. ONLY ON INTEGRATED OVEN 22" x 23.6" x 22"

The ankle foam fills the hollow below and behind the ankle to wedge the heel in place. The level 2 liner contains a foam made in an exclusive Wed'ze material and shape: - the shape was based on an average of 40 foot scans. It is perfect for holding the foot tightly and adapts to everyone - the material: a soft but firm elastomer foam. You can feel the support as soon as you slip your feet inside. And when you're riding, you'll feel no hard areas.

On this liner, we kept just 2 points of tightening with the laces: - at the instep - above the ankle At the top of the liner, we replaced the 3rd lacing point with a powerful clamping strap. We have therefore reduced the friction from the lace (2 points instead of 3) and used the clamping force to support the heel. On the upper part, the strap locks the liner even tighter over the shin.

We've added a rip-tab at the back between the liner and the shoe. The aim? Limit slipping of the liner on the inside of the shoe to help you better control your board because it is not enough to keep your foot in the liner: if the liner moves in your shoe, you will not steer your board as effectively.

This shoe has a 3D insole. This sole is pre-shaped at the heel and arch of the foot to help prevent the foot from moving inside the boot. It offers comfort and thermal insulation. If you feel you need to maintain your foot more securely in the boot, there is another alternative: get a sole that is thermoformed to suit your foot. This is the most efficient solution.

Our Ultralight sole is only in EVA. EVA is a very light material with 80% air. This formulation is designed to resist abrasion while keeping its damping properties. It is naturally very insulating and protects against the cold rising from the ground. We designed in large studs to offer you very good grip. They are spaced quite far apart to prevent snow from getting stuck.

Imported

At the end of the day, remove the liner from the upper to improve ventilation and dry quickly. Also, remove the inner sole from the liner to dry fully in 1 night.