Quechua NH500, Waterproof Off-Road Mid Hiking Boots, Men's

The sole’s design is the result of extensive research carried out in our labs. We favored a specific rubber formula that optimizes grip and resistance. As the requirements are not the same, we systematically look for the best compromise for hiking on loose off-road terrain (like a forest path) as well as hard, stony trails (like a coastal path).

Our hiking boots are designed for use on off-road trails. Indeed, we choose the components of the sole and upper of our boots and test them to ensure that they are ideally suited to hiking on loose trails (e.g. unpaved forest paths) or rocky trails (e.g. rocky coastal paths). Road use (asphalt) may lead to premature wear on your boots and cause discomfort. They are not suitable for mountain hiking.

For these boots, we have chosen components that are more respectful of the environment: - Upper (front of the boot, flap, and top of the boot): 52% recycled polyester and 48% dope dyed polyamide (dye using less water) - tongue and ankle support lining: 100% recycled polyester - Laces and loops: 100% recycled polyester - Insole: 85% recycled polyurethane foam and 100% polyester lining - Outsole: 30% recycled rubber

We use a leather called nubuck. It has a soft, silky feel. The leather used on these boots comes from cows We do not kill any animals to obtain this leather: We only use waste from the food industry. The leather on these boots comes from French skins that are then tanned in Spain.

After your hikes, we advise you to: - Dry your boots away from any heat sources - Brush the dry leather vigorously with a stiff brush to remove mud and dirt - Use a crepe brush or nubuck rubber to remove stains - If the stains persist, clean with a brush and a little warm water - Leave to dry - Brush again with a stiff brush - Use spray-on waterproofing: This will make the leather shine and bring out the colors

Footwear equipped with a membrane is laboratory and field tested to ensure optimal waterproofing and breathability. To start, they are immersed in water with pressurized air inside to check that no bubbles form on the surface of the boot. Next, they are fitted to a mechanical arm that simulates walking half-immersed in water to test that the inside remains perfectly dry.

In the impermeability test, we test 3 levels of waterproofing: - 2000 flexes, about 2 hours of hiking - 4000 flexes, about 4 hours of hiking - 8000 flexes, about 8 hours of hiking The NH500 Mid WP men's boots were tested for 8000 flexes in the laboratory. This means they will stay waterproof for an 8-hour hike. Of course, as soon as the boots are dry, they become waterproof again.

Laboratory tests were also conducted to test the following elements: tearing eyelets and straps, gluing, toxicology, UV resistance, abrasion resistance of outsole and upper components, accelerated aging. These tests allow us to improve the quality of our products and prevent premature wear of our hiking boots.

We advise that you use a re-waterproofing spray several times per year, to restore the original water-repellency and prevent staining.

Try on both boots, standing up and wearing the socks you use for hiking. Try on several models or sizes if necessary. Check 2 comfort points: - the heel seating - the front of the foot on a downward slope Avoid any pressure points when fitting. Feel free to walk around the store. Gradually start using your boots during your 1st few hiking trips to break them in.

There are multiple factors that may cause blisters when you are walking: rubbing, a crease in the sock, moisture, a shoe size that is too small or too big, etc. It is therefore important to choose the right size and to have socks made of the right material for your hiking boots.

You must choose the right sock size for your foot so that there are no additional creases in the sock: either because the sock is too big and there is too much fabric around your foot, or because the sock too small and is pulled down into the boot.

Moisture must be effectively managed when hiking: We sweat; it’s bound to happen. If your boot is breathable, it will wick away moisture from your perspiration. It is therefore necessary to choose a light and breathable sock as well. If your boots are relatively waterproof, you will not make the same choice to protect you from the moisture of the rain: Choose a sock that will absorb your sweat, and direct it as far as possible away from your foot.

Although the waterproof membrane of these boots is breathable, they do not eliminate the moisture of your perspiration as effectively as a ventilated boot. You should opt for the NH500 High socks: They contain moisture-absorbing cotton and have a reverse terry-knit construction under the sock that wicks moisture away from your foot. They are high enough to protect your ankle from the boot. It's an excellent combination for reducing the chance of blisters.

Our hiking boots are guaranteed for 2 years. Our commitment? To offer you long-lasting products that you can use on all your hikes and walks. Because the products that we love the most are those that have lived the most adventures and will continue to live them!

Imported

Our design team conceives, designs, and creates Quechua products in France, at the foot of Mont Blanc. We test them in the field with other hikers, to check their comfort and durability. Fontainebleau Forest or in Brittany, for example. We go on as many trails as possible, in all weather conditions. This creates plenty of opportunities for discussion to get your feedback, which is used to plan our future products!

We recommend you store your boots in a dry, dark, and, if possible, ventilated place.