Wedze Serenity 500 Snowboarding Boots

Upper of: 100.0% Polyurethane ; Outer sole of: 100.0% Ethylene Vinyl Acetate ; Lining and sock of: 100.0% Polyester cationic ; Warm lining: 100.0% Polyester cationic

The Serenity 500 snowboard boots are an improved version of the previous model. In addition to its more feminine lines, we have added technical improvements: _ this model now has 2 tightening zones: a rip-tab on the shin adjusts the stiffness of the boot (the tighter it is, the stiffer it gets) and a tightening system on the instep with a knob and cable for great support._ the improvements in the comfort of the All Road 500 boots have also been applied to the Serenity 500.Enjoy your ride.

_Cable Lock: very powerful cable tightening knob._ 2Z = 2 tightening zones.The tightening of the knob is focused on the instep to provide good support, and the rip-tab at the top prevents unwanted shin movements inside the snowboard boots. During the design work, we did a lot of testing with and without the rip-tab on the top of the boot. It provided so much support that we kept it.

The Serenity 500 has a medium flex (5/10).It’s for people who take turns at high speeds (need a stiff boot) while also providing quick handling in tight turns or surprise bumps, where you need to rapidly bend and extend your legs. The flex and heel support are both superior than the Maoke 300 boot.

Foot support is essential when snowboarding, to be able to correctly steer your board (foot in the liner, and liner in the boot).The level 2 liner applies 5 concepts: 1. liner that can be thermoformed at home2. ”Ergonomic Heel Pad”3. ”2 point + scratch” liner tightening system,4. ”Hook and Loop Link” link between the liner and boot

THERMOFORMING IS ONLY POSSIBLE IN BUILT-IN 22” x 23.6” x 22” (56 x 60 x 56 cm) CONVECTION OVENS.DO NOT TRY ON A GAS OVEN OR A MINI OVEN WITH VISIBLE HEATING ELEMENTS.

1. Heat your oven to 175°F with the fan on 2. Remove the inner soles of the liners, and place the liners on the oven plate with some greaseproof baking paper3. Wait 15 min4. Put the insoles back in. Put on a pair of ski-snowboard socks. Put on the liners and tighten fully.5. Put the boots on, tighten them up fully and wait for 15 minutes, without movingYou can repeat the process if you feel discomfort or a lack of support.

The ankle bone padding fills the hollow under and behind the ankle to hold the heel firmly in place.The level 2 liner contains a foam made in an exclusive Wed'ze material and shape:- the shape is based on an average of 40 foot scans. It’s perfect for holding the foot in place and adapts to everyone- the material: a soft but firm elastomer foam.You can feel the support as soon as you slip your feet inside. And when you ride, there are no hard points.

On this liner, we retained only 2 tightening points with laces: - at the instep- above the ankleAt the top of the liner, we replaced the 3rd lacing point with a powerful rip-tab strap.We therefore reduced the friction of the laces (2 points instead of 3) and focused the tightening force to provide heel support. On the top part, the rip-tab easily holds the tongue in place.

We added a rip-tab on the back between the liner and the boot.The aim? To stop the liner from slipping inside the boot to help you better control your board, because it’s not enough just to hold your foot in the liner: if the liner moves inside the boot, you’ll be less able to control your board properly.

All the Dreamscape by Decathlon products are tested in the real-life conditions of use for which they were designed. In the snow, in the cold, and in all the conditions that you may encounter when snowboarding, whether it is in powder snow, in the snow park, or on piste. The design teams, product managers, designers, and engineers check that the program for which the product was designed and developed perfectly matches its use in the field.

At the end of the day, remove the liner from the upper to help with ventilation for quick drying. Also remove the liner’s inner sole to dry thoroughly overnight.

Imported