Women's waterproof mountain walking boots MH100 – Blue Plum

Outer sole of: 70.0% Synthetic Rubber, 30.0% Ethylene Vinyl Acetate ; Upper of: 60.0% Polyester, 20.0% Polyurethane, 20.0% Leather - Bovine - Split ; Lining and sock of: 80.0% Polyester, 10.0% Polyurethane, 10.0% Polyamide

We have classified our products in terms of performance and features for 3 levels of Mountain Walking:- occasional: about 10 hikes per year of about 3 to 4 hours in length, covering less than 10km and less than 700m in elevation gain.- Regular: about 20 outings per year. 4 to 6 hours, 10 to 20 km, 700 to 1200m of elevation gain per outing.- Intensive: more than 20 times a year. More than 6 hours, more than 20 km, 1200 to 2000m of elevation gain per outing.

For the inner sole fabric coating of these boots, we dye the thread during manufacturing to reduce the environmental impact. Textile dyeing requires a lot of water but also produces waste water from the dye baths. To reduce this environmental impact, we use a mass pigmentation process that involves adding the colour pigments when the yarn itself is produced.

The grip of our soles is certified. To be awarded certification, the boots must pass laboratory tests to assess the grip rate on different surfaces (Smooth, Rugged, Dry, Wet). To validate these tests, we assess the quality of our soles in the field, in the mountains, by a panel of representative testers over 500 km

In a laboratory, the boot is immersed in water to mid-height on a mechanical arm that flexes to simulates a number of steps. With this test we can determine a time and number of km that the boot can walk while staying dry. Then we confirm in the field or under the rain, that the shoe meets its promises.

To keep your feet dry, we advise you to use a gaiter or mini-gaiter to protect the top of your boots and prevent water and also pebbles and sand from getting in We advise re-waterproofing your boots twice a year using a re-proofing agent (search for ‘waterproofing’ on our decathlon website) which will help you restore the original water-repellent qualities and fight against stains on the outside.

‘The most important thing is to try on several styles of boots to find the one most suited to you! You can take a size above your usual one to prevent the toes from bumping into the toe box when going downhill, provided the foot is properly supported to avoid friction.Tip: keep your toenails short and, before descending, check that your lacing prevents your foot from sliding forwards inside the shoe.”

Some Decathlon stores have a test route.1. Try on both shoes, standing up, with the socks worn for hiking. 2. Tighten the laces, taking care to correctly balance the tightening.3. Check two points:- the heel does not come up before the boot when you walk uphill.- the foot does not slide and the toes do not press against the front when going downhill.4. Try on several sizes and models.Break them in gradually to adapt them to your foot.

The original insole in your boots is designed to accommodate most feet. A change of insole can bring:1. Improved support: some soles are preformed or reinforced to better support the arch of the foot. 2. More comfort: the insoles can also provide heat and/or cushioning.3. Longer life: restore the support and comfort of your shoes by replacing the insole each season.

Blisters generally develop when the skin is weakened by friction. In order to prevent them from occurring, we recommend the following: - Choose a shoe in your size.- Wear suitable socks- Tie and tighten your shoes properly.- Make sure you tighten or loosen your laces accordingly while wearing your shoes, especially before starting a climb or a descent. - Wear your shoes on a short trip for the first use.

All our boots are tested for initial comfort and comfort in use by hikers from outside Decathlon under the same conditions you find in use. The aim is to test, develop and confirm the product in the most objective way possible, so you can get maximum enjoyment out of hiking!

Store in a well-ventilated dark, dry place.

Imported